Machine.Glass

Dark Blue EVAVISION transparent EVA interlayer film for laminated safety glass

EVA Thermal Cutter
to clean laminated glass edges overflowed remains of EVA, PVB, SGP etc.
Application:
When making laminated glass with EVA film(or PVB film, SGP film) there may be some overflowed EVA remains (or PVB remains, SGP remains) on the edges of laminated glass after heating in the oven, EVA Thermal Cutter is the handhold tool to clean the laminated glass edges remains easily.

How it work:
The blade of the EVA Thermal Cutter can be up to 500℃ in seconds. The EVA Thermal Cutter use the ultra high temperature heat to cut the EVA remains (or PVB remains, SGP remains) of the laminated glass edges.

The EVA Thermal Cutter cleans the overflowed remains NOT by strength or sharp, but by Ultra High Temperature Heat: 500℃. So whether the interlayer film is EVA FILM, PVB FILM, or SGP INTERLAYER, the result is the same.

Data:
CE Plug: AC 230V/50HZ
US Plug: AC 120V/60HZ
Temperature of Blades: Up to 500 ℃ in in approx 5-7 seconds
Thermal Cutter is available in 4 shapes of blades to remove the remains of laminated glass edge.

Comments from Our Clients:
*Comment1:
Peter,
The Thermal Cutters were received 10/9, in the afternoon. I have already used them and they work great. Much better than the method I was using before.
*Comment2:
Dear Olivia,
My people are very happy with the cutting tool.
*Comment3
Peter,
Yes, we received the cutters. We have already been using them and they work very nicely.Thank you for your help.
*Comment4
Dear Olivia,
We have good result with EVA thermal cutter, my colleague will contact you to place new order.

CNC Glass Interlayer
www.cncglass.com www.c-n-c.com
[email protected] [email protected]
Product 1]Super Clear EVA Film for safety laminated glass
Product 2]Milky White EVA Film for safety laminated glass
Product 3]Green Tape and Thermal Cleaning Cutter for EVA film safety laminated glass glazing

EVA Thermal Cutter
to clean laminated glass edges overflowed remains of EVA, PVB, SGP etc.
Technical Data:
CE Standard: AC 230V/50Hz
US Standard: AC 120V/60HZ
Power: MAX 90W
Temperature of Blades: Up to 500℃ in seconds

Preparation:
A-Select a Thermal Cutter blade corresponding to the cutting use.
B-Loosen the knurled nut when device is cold.
C-Insert each leg of the blade and tighten the knurled nuts. Make sure that the blade and the cutting head have optimal contact. If both legs of the blade are not properly installed, the unit will not heat up.
D-Power on.

Cutting:
A-Actuate switch, the indicator light and the blade will heat up.
B-Avoid direct short circuit between cutting heads.
C-Do not use metallic rulers for guiding the blade.
D-Clean cutting heads with enclosed wire brush.
E-Please make sure the blade is connected to the cutting material before blade heats up.

Caution:
A-Always operate the Thermal Cutter in well ventilated space.
B-Never burn off the excess residue on the Thermal Cutter blade. The blades will over heated and be warped.
C-Only operate Thermal Cutter when it is in contact with the insulation board
D-Keep hot blades away from skin, clothing and other flammable materials.
E-Allow blades to cool before handling. Thermal Cutter may cause injury or burns to exposed surfaces.
F-The Thermal cutter is working intermittently, that means If the temperature inside the tool is too high, the unit will get hot and the internal thermal protectors will turn off automatically, after it cool, the Thermal Cutter will operate again.

EVA THERMAL CUTTER, PET GREEN TAPE, supporting EVALAM interlayer film lamination